Just How to Set up a Bathtub Yourself
Just How to Set up a Bathtub Yourself
Blog Article
The content down below relating to A Step-by-Step Guide to Installing a Bathtub is exceedingly informative. Read it yourself and figure out what you think of it.
Mounting a bathtub isn't specifically rocket science, yet it does need solid plumbing, carpentry, and occasionally, tiling abilities. Replacing an old tub with a brand-new one is also a moderately difficult job. If the old tub is conveniently available, the job can move immediately; if you have to open up a wall surface to eliminate the old bathtub as well as place the new tub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will certainly require an assistant to vacate the old bathtub and also set in the brand-new one. Make sure you have certified yourself for the task and also are comfortable attempting it. As opposed to employing a service provider to take over a halfway-completed job, it is far better to think about using one before you start. Chances are you may require an expert plumber to make tube links.
This short article will certainly aid you install a new tub in your washroom if you have currently acquired a new tub and don't require to transform the setup of your previous water supply pipes.
Your tools as well as product list need to consist of the following:
Getting ready for the Setup
First of all, the sustaining framework supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is essential to ensure that if the tap comes with a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps device to stop stress on the tub.
Fit the versatile tap adapters to the bottom of both faucets utilizing 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its last placement.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you must do is disconnect the water. After doing so, turn on the faucets to drain any kind of water staying in the system. The procedure of eliminating the existing taps can be fairly problematic as a result of the restricted access that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a fabric all set for the staying water that will certainly come from the pipelines. As soon as the supply pipes have actually been gotten rid of, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming throughout this process. When the faucets have been eliminated, the holes in the bath/basin will need to be cleansed of any kind of old securing substance.
Prior to moving on to fit the new faucets, contrast the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Setting up the Bath tub
Using the two wood boards under its feet, position the bath tub in the required setting. The wood boards are useful in equally spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little factors.
The following goal is to guarantee that the tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bath tub until the spirit level checks out level.
To set up taps, fit all-time low of the outermost flexible tap port to the proper supply pipeline by making a compression sign up with; then do the very same for the various other faucet.
Switch on the supply of water as well as inspect all joints and also brand-new pipework for leakages and also tighten them if essential. Fill the bathtub and also inspect the overflow outlet as well as the typical outlet for leaks.
Finally, repair the bathroom paneling as explained in the maker's user's manual. Tiling as well as sealing around the bathtub ought to wait until the bathtub has been used at least once as this will settle it into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the tap as well as the other end offers a link to the existing supply pipelines.
If you need to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin making sure that the washing machines are in location between the tap and the sink. Secure the tap in place with the supplier given backnut. As soon as the faucet is safely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular faucet connectors. The former kind must be connected to the tap finishes initially, tightening just by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath fulfills the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to crack an inflexible seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, resulting in complications with moisture and also feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your components and also fittings. They are marketed in tubes as well as cartridges, and can sealing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the tub with water prior to sealing, to enable the movement experienced when the bathtub is in usage. The sealant can split fairly early if you do not take into consideration this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently available on the marketplace. It is a good idea to fit the floor tiles making use of water-resistant or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were brought to that report on How to Install a Bathtub Yourself through an acquaintance on our other blog. Sharing is good. One never knows, you may just be helping someone out. I enjoy reading our article about How to Install a Bathtub Yourself.
Set An Appointment
Report this page